Selection Oak

Oak wood as the source of inspiration with warm tones selected with refined precision to recall the pale atmospheres of the sea and the relaxing colours of virgin forest woods.

Certified
Quality
Learn more
Selection Oak

Rex has chosen a new style for design, a surface that is strongly reminiscent of nature and communicates multiple aesthetic suggestions on these ceramic stoneware tiles. Relaxing simplicity and aesthetic austerity that interact with the atmospheres of the home and the raw appeal of vital living energy on exterior and interior design.

Modern design perspectives are about to change: amazing sizes, just 6 mm thick.
  • 26,5x240 cm
  • 26,5x240 cm
  • 26,5x240 cm
  • 26,5x240 cm
Print this page
Specification referenceE.N. 14411 . Appendix G. Group BⅠa. UGLTest methodReference valueDeclared value
Static coefficient of frictionASTM-C1028>0,60 dry and wet> 0,6 dry and wet
Dynamic coefficient of friction (section 9.6 ANSI A 137.1 2012)DCOF>0,42 wet> 0,42 wet 
Barefoot slip resistanceDIN-51097-Cl. A+B (sp. / thickness / ép. / Dicke / gr. 20mm) 
Barefoot slip resistance-Cl. C (sp. / thickness / ép. / Dicke / gr. 10mm)
SLATE-HAMMERED
Slip resistance with shoesDIN-51130:2010-R11
SLATE-HAMMERED
Slip resistance with shoes-R9
MATTE
Slip resistance with shoes-R11 (sp. / thickness / ép. / Dicke / gr. 20mm) 
Frost resistanceISO-10545-12Richiesta / Required / Requise / Gefordert / RequeridaRESISTE / RESISTANT / RÉSISTE / ERFÜLLT / RESISTE
Resistance to low concentrations of acids and alkaliISO-10545-13Come dichiarato dal produttore / See manufacturer’s declaration / Selon déclaration du producteur / Entsprechend der Herstellerangaben / Tal como declara el fabricanteULA 
Resistance to domestic chemicals and additives for swimming poolsUB minimo / UB minimum / UB minimum / UB mindestens / UB minimoUA 
Resistance to stainingISO-10545-14-CLASSE 4 / CLASSE 4 / CLASS 4 / GRUPPE 4 / CLASE 4 
Maximum right-angle deviation, in %, in relation to the corresponding production dimensionsISO-10545-2±0,5% (±2 mm)± 0,20% 
Maximum straightness deviation, in %, in relation to the corresponding production dimensions±0,5% (±1,5 mm)± 0,10% 
Admitted deviation, in %, of the average thickness of each tile from the production dimensions±5% (±0,5 mm)± 5% 
Surface qualityIl 95% min delle piastrelle deve essere esente da difetti visibili / At least 95% of the tiles must be free from visible flaws / 95% min des carreaux ne doivent présenter aucun défaut visible / Mindestens 95% der Fliesen müssen frei von sichtbaren / mín. el 95% de las baldosas tiene que estar exento de defectos visiblesCONFORME / CONFORMING / CONFORME / ENTSPRICHT / CONFORME 
Length and width: admitted deviation, in %, of the average size of each tile from the production dimensions±0,6% (±2 mm)± 0,15% 
Flatness (centre curvature / edge curvature / warpage)±0,5% (±2mm)± 0,35% 
Amount of water absorbed, in percentageISO-10545-3E<0,5%average value 0,08% 
Bending strength in N/mm2ISO-10545-4>35 N/mm2average value 50 (sp. / thickness / ép. / Dicke / gr. 10mm) 
Breaking strength in N (thickness >= 7,5 mm)≥1300 Newtonaverage value 14000 (sp. / thickness / ép. / Dicke / gr. 20mm) 
Breaking strength in N (thickness >= 7,5 mm)≥1300 Newtonaverage value 3200 (sp. / thickness / ép. / Dicke / gr. 10mm) 
Bending strength in N/mm2>35 N/mm2average value 52 (sp. / thickness / ép. / Dicke / gr. 20mm) 
Resistance to deep abrasion of unglazed tilesISO-10545-6<175 mm3average value 140 
Thermal shock resistanceISO-10545-9-RESISTE / RESISTANT / RÉSISTE / ERFÜLLT / RESISTE 

Notes

  • For optimal installation results, Florim recommends maintaining a joint of 2 mm 1/12” for single format installations and 3 mm 1/8” to combine mixed formats.

     
  • The data in the technical table does not apply to Florim Magnum Oversize products.

     
Bureau Veritas Selection Oak Outdoor
CE Selection Oak
CE Selection Oak Magnum
GREENGUARD
LEED Selection Oak
LEED Selection Oak 20mm